Detta arbete tar upp utvecklingen av ett nytt protokoll för användning inom Home Automation över IP-nätverk, med stor vikt på flexibilitet och enkelhet. Vi valde att utveckla ett nytt protokoll för Home Automation då en granskning av dagens protokoll visar att dessa inte är tillräckligt öppna eller flexibla för att passa alla enheter som används eller alla scenarion som kan uppstå.I våra litteraturstudier samlades information in som skapade grunderna för vårt protokoll och gav oss en större inblick i teknikerna bakom dagens tekniker inom home automation. Detta gav oss även möjlighet att senare jämföra vårt färdiga protokoll med redan existerande protokoll för att se om vi lyckats skapa något som kan användas. Metoden vi valde för att utveckla protokollet är en generell designmetod där vi efter granskningen av tidigare protokoll tar fram ett antal punkter som det nya protokollet skall uppnå. Det visade sig dock vara problematiskt att få fram svar om vissa protokoll så vi frångick metoden genom att istället utveckla protokollet utefter ett antal olika scenarion som det bör kunna hantera.Resultatet av arbetet är ett protokoll som uppfyllde nästan alla mål vi satt upp för det.

Building Automation Systems in commercial buildings are often designed and installed by different contractors, using equipment and components from different manufacturers. The lack of an accepted communication standard has resulted in a few different standards. Many manufacturers of building automation systems only support one, a few or none of these standards, while developing proprietary system solutions. Regin, who develop such equipment, are planning to adopt an open communication protocol specially designed for building automation - BACnet. As a step in that direction this thesis was announced with the purpose to investigate the possibility to implement BACnet in one of their products and to gain more knowledge of the BACnet protocol.

Today all buildings contain some form of home automation. It might be heating controlled by athermostat or motion detectors controlling outdoor lighting.This paper,The Intelligent House, deals with the planning of a house in Kiruna, in the north ofSweden and further immerses itself in home automation or intelligent control in single-familyhomes. The house has been entirely planned, from layout to structural design and plumbing.The purpose of the paper has been to investigate the possibilities in home automation in singlefamilyhomes and to choose a suitable home automation system for the house being planned.The system has been designed and the costs and energy savings have been calculated.The system chosen for the house is called KNX and is the largest system for home automation inSweden. It is used to control heating, ventilation, lighting and alarm systems in the house. Is hasbeen found that KNX is very expensive and that the amount of energy, possible to save in thehouse, using the system, is relatively small.

In today's society there is a significant focus on energy efficiency. Despite this, people leave lamps, televisions and computer screens etc. powered on unnecessarily. The goal of this project is to build a simple prototype for home automation where a user, via an application on a mobile phone, can switch on and off the power of an electrical products in the home and as well as being able to check whether such products are switched on or off. The prototype will also collect data on power consumption for these electrical products.

Arbetet tar upp BGP-multihoming för mindre organisationer. Den jämför ett kommersiell alternativ mot open source-alternativ. Detta är för att se vad som krävs en av open source-lösning för ge konkurrens på routermarknaden, samt besparingar för organisationer som ska använda denna lösning.Praktiska och teoretiska jämförelser görs där Cisco-lösningar jämförs med OpenBGPD. Datan utifrån dessa tester används för att svara på problemfrågan. Sammanfattningsvis har open source produkter en fördel hårdvarumässigt på grund av lägre kostnader medan kommersiella har stora fördelar då de förlitar sig på nyare standarder..

This report describes the design and implementation of a multi-master, packet based protocol for small and tiny microcontrollers where resources are limited. The protocol was named "Tiny Controller Network" or TCN for short. The protocol is meant mainly as a control bus for automation and sensor acquisition applications but due to its flexibility can also be used for other purposes as well. It borrows some of its functionality and design ideas from the well known CAN bus and Modbus but also has a number of major differences like the use of standard hardware and time synchronisation. One of the key aspects during the design was the use of very little system resources and common on-chip hardware peripherals like a UART.

This report describes the design and implementation of a multi-master, packet based protocol for small and tiny microcontrollers where resources are limited. The protocol was named "Tiny Controller Network" or TCN for short. The protocol is meant mainly as a control bus for automation and sensor acquisition applications but due to its flexibility can also be used for other purposes as well. It borrows some of its functionality and design ideas from the well known CAN bus and Modbus but also has a number of major differences like the use of standard hardware and time synchronisation. One of the key aspects during the design was the use of very little system resources and common on-chip hardware peripherals like a UART.

This report is based on a thesis that was carried out during spring 2012. The report covers the development of a preliminary study to Performance Sk8. The purpose of the study is to facilitate and contribute inspiration to Performance Sk8 to run an automation project to bring home their production to Sweden from China. The reason is to gain a greater ability to control quality, produce smaller batches and reduce the cycle time to reduce costs.The goal is that the preliminary study shall meet the requirements and wishes Performance Sk8 and other partners defined. The pre study will contain different cost proposals for the automation of selected process and serve as a basis for procurement of the equipment.The pre study has resulted in some proposed solutions to the various steps required to automate Performance Sk8 ?s production.

SMTP, the current protocol for sending electronic mail (e-mail) over the Internet, has for many years suffered from several problems and limitations. When it was designed, well over twenty years ago, the requirements for e-mail were very different from those of today. A message was a text message in English, and both user and machine were explicitly named in the address. The protocol was not designed to transfer other types of messages, and no mechanism was included to verify the identity of the sender.In order to solve these shortcomings, a new e-mail protocol needs to be defined. This report specifies a basis for what such a protocol may look like.

The Internet protocol of today has been used for over 20 years. A new version of the protocol has been developed to replace the old one. This is a direct result due to the explosive growth of the usage of the Internet. This follows by new demands which needs new solutions. This report brings up the old protocol IPv4, the new protocol IPv6 and shows what kind of changes that has been developed to meet the users demand.The report brings up two important aspects; internet security and mobility.

Det problem som denna uppsats hade för avsikt att besvara var varför hemautomation inte används i fler hem. Genom resultaten från en enkät som distribuerades kunde slutsatsen att kostnaden för de befintliga lösningar som finns på marknaden idag inte låg i den prisklass våra respondenter ansåg rimlig. Författarna utvecklade då problemet och ställde sig frågan om en hemautomationslösning verkligen måste ha en så hög kostnad som de befintliga lösningarna har idag. För att belysa detta problem implementerades en egen kostnadseffektiv lösning där respondenternas mest önskvärda funktioner togs i beaktande och en testmiljö implementerades utefter dessa. Resultatet blev en hemautomationslösning med stor potential och med en betydligt lägre kostnad än dagens befintliga lösningar..

As a part of Göteborg Energi?s work towards a smarter electric grid, the company has chosen to investigate the possibilities of automation in their middle voltage grid. In Europe, there are example cases where these technologies already are installed which many articles on the CIRED conference 2011 proved. Netcontrol Oy in Finland has, together with Tekla, created an automated SCADA system that Vattenfall in Finland today uses. The grid mainly consists of 10 kV open loop fed city grid and this automation is mainly designed for this type of grid.

In today?s IT world where software is constructed in a rapid pace, testing has become a crucial area to master when testing has to be done at a greater speed. To still be able to handle the demands of high quality software, companies have to spend more resources on testing and introduce test automation. By automating test cases the testers can gain time which they can spend on doing more complex testing and thereby increase the quality of the software.In this thesis we have helped Extenda AB, who delivers systems to retail companies, to introduce test automation in one of their customer specific projects. This has been done using their own in-house ?capture/replay? tool ECP (Extenda Cashier Player).We have also derived a process that explains how Extenda can introduce test automation on other customer projects.

The remotely operated underwater vehicles that the client develops have needs of different kinds of data channels. In order to minimize the need of physical cable between the control unit and a ROV, a multiplex protocol has been developed. The protocol has been designed with the aim of using the bandwidth of the transferring link as efficient as possible.The different kinds of data channels used during this thesis project is; RS232, RS485 and CAN. ROM and FIFO-memories have been used to be able to effectively manage the different data channels. All the reading and sending of these channels have been implemented in FPGA-technology, the coding is made generic so that it will be easier to add more channels to the system in the future.The multiplex protocol is a modified version of the method STDM and it is a proprietary protocol.

This thesis is a case study which describes the automation of a university library in Sub-Saharan Africa. The aim of the case study is, firstly; to find out which actors and factors have started and influenced the automation and the implementation of ICT at Makerere University Library in Kampala, Uganda. Secondly; it also discusses if the automation has changed the librarys condition. The empirical material consists of fifteen interviews with librarians and students. The empirical material itself has functioned as a base when discerning the analytical themes.